Marble Cleaning, Polishing & Restoration

If every day wear and tear has removed the luster from your marble floors it's time to call Capitol  for our special marble polishing system.

Conventional marble polishing is done by using a diamond-coated pad to sand the marble. This process removes a thin layer of the marble to produce the desired sheen.

But now there is a new system that will leave the marble sparkling like new, but it is much less abrasive. It's dust free, it's fast and it produces results so stunning you'll be amazed.

Here is some sound advice when it comes to Marble maintenance. It must be said that if it can be afforded Marble maintenance should be performed by expert Marble, Slate, Terrazzo and Granite Restoration companies such as ours.

We realise that that isn't always practical and affordable so here is a listing of marble maintenance that you can sometimes do yourself.

Initially non polished or "honed" marble, granite, and limestone were used for flooring because they were an inexpensive building material that was highly durable and easy to maintain. This unpolished finish only required sweeping and mopping to keep it clean.

To maintain your stone floor you must be familiar with standard maintenance procedures, and with the specialized techniques used to polish stone floors, so you can build a proper maintenance program to suit your needs and keep your floor in its original condition.

The main types of stone used today in flooring are marble, granite and limestone.

Granite has little or no veining and can have solid backgrounds with shiny specks or flecks of crystals throughout the surface.

Limestone usually ranges in colour from grey to buff and is usually consistent in colour with little or no veining. Limestone sometimes has imbedded fossils, iron streaks and streaks of calcite as other identifying features. Limestone floors are soft and scratch easily. These can be polished by various methods but will generally not achieve a mirror like shine.

Marble comes in a wide range of colours usually with veins and variant colours running through it. It ranges from soft to very hard and will polish well to a deep mirror like reflection.



Marble Maintenance

The first step in developing a floor maintenance plan is to determine the current condition of the stone. Some common problems and recommended treatments are listed below. A professional marble restoration company can diagnose all these and other problems and give you an evaluation of what the present condition is and what is needed to bring your marble back to its original finish.

Cracks may be repaired by filling with a suitable filler material. Very large cracks, or very small hair line cracks, cannot generally be filled and the only alternative is replacement.

Stun marks are caused by sharp impact on the stone surface. The most common cause of stun marks are ladies high heeled shoes. These marks are sometimes very deep in the stone. Grinding with diamond abrasives can remove or improve some, but if not then replacement of the damaged stone is the only alternative.

Deep scratches can usually be repaired by resurfacing with medium to coarse grit diamond abrasives.

Etching is a dull area on a stone caused by spills of acidic products such as citrus juice, vinegar, soft drinks, etc. If the etching is very light it possibly can be repaired by polishing the area with a crystallizer or polishing powder. Heavy etching must be repaired by resurfacing the area with diamond abrasives.

Lippage or uneven tiles must be ground down or bevelled to alleviate the problem. This is done by grinding with coarse grit diamond or abrasive stones.

Spalling is a condition in which piece of stone has broken leaving a chip or hole in the face of the stone. These can be repaired by filling with a polyester, epoxy or cement based filler material coloured to match the stone. The affected area must be resurfaced after filling to level the filler material to the stone surface. Replacing the stones is another, but more costly, alternative.

Staining, in most cases, can be remedied by a process known as "poulticing". The appropriate poultice for the stain is prepared and placed on the stain and allowed to dry. As it dries it draws the stain out of the stone. If this method doesn't work, "honing" (grinding) the surface down to a fresh layer of stone and then re-polishing may be needed to remove the stain. Poultice powders can be purchased from here at allbright and shiny

Yellowing , in white marbles, can be cause by iron present in the stone that oxidizes over time. Unfortunately since the yellowing is from the nature of the stone the only treatment is replacement. More commonly yellowing is cause by ground in dirt or wax coatings that turn yellow. This type of yellowing can be repaired by stripping off the coating and cleaning the stone well.

Daily maintenance is very simple, damp mop daily. The loss of polish on stone floors is mostly caused by dust, dirt, sand and other fine particles scratching the surface from foot traffic. Removing the dust and dirt from the floor will help keep this scratching to a minimum. The less scratching that occurs, the less frequently polishing or restoration will be needed. A good quality cotton mop works best. Do not over wet the floor, light damp mopping is all that is needed. If grout lines start to darken scrub well and wet vac out debris.

Make certain that the cleaner you use has a neutral pH of seven. High alkaline or mild acidic cleaners can dull or damage the finish, particularly "no streak" cleaners. Although they may be neutral pH seven some contain "Chelates" which dissolve or destroy calcium in the water and eliminate hard water deposits. Since marble and stone contain a large amount of calcium these cleaners attack the finish on stone floors.

Hint: You can test whether your cleaner is neutral by pouring a drop of the concentrated cleaner in an inconspicuous location and let it sit for 5-10 minutes then wipe up. If the spot is dull then the cleaner is not neutral and will etch your floor, but if no change is observed in the finish it should be fine.

Methods of Polishing and Restoration

Sanding with diamond abrasives is the most durable polishing method and is also the only choice for restoration. This method involves grinding the floor down with commercial grade diamond abrasive pads. Successively finer pads are used to bringing out a mirror like shine.

Polishing powders can also give very effective results. In this method polishing powder is applied with a buffing machine to bring out a mirror like shine. This is a good regular maintenance choice.

Coatings like wax and urethane are used as quick fixes and are more of a problem than a solution. These coatings prevent the stone from "breathing" and may yellow light colored stones, and the chemicals used for stripping the coatings off can damage the floor. These finishes are no answer to imperfections in a stone floor and in the long run may only exacerbate problems. The best approach is to not use coatings at all.

Which method is best?

The only sure method of polishing all forms of granite floors is by sanding with diamond abrasives and/or polishing powders. A chemical spray and buff method is available for dark colored granite. Granite is very scratch and acid resistant so the need to polish is very rare. Daily dust and damp mopping is all that is needed to maintain the finish.

Marble and Limestone are very effectively treated by all methods. Diamond abrasives are the best choice if there are minor imperfections in the stone that need to be ground out before restoration, and if a tough durable finish is desired.

No matter which method is used polishing should be done regularly . Once the finish goes dull it takes three to four times longer to bring it back. Your polishing schedule will be determined by how well the stone is cared for on a daily basis and the level of traffic on the floor.

For commercial applications, polishing main traffic areas like lobbies and entrances should be done frequently while low traffic areas may need to be polished less frequently.

With heavier traffic levels, commercial sites will need polishing a weekly or monthly basis. Residential floors can usually be done on yearly or twice yearly polishing schedules due to significantly lower traffic levels.

The best way to decide on a polishing schedule is to polish the floor and observe how long it takes for the floor to begin to dull. The floor should then be polished and a schedule set up to suit that observed pattern of wear. Over time high traffic areas may become too worn down to polish to a deep shine. When this happens the area should be restored with diamond abrasives to bring back the original clarity and depth.

Impregnators/Sealers

When getting your floor refinished, having it treated with an impregnator or sealer would be a good idea. Untreated stone can stain very easily. Treating these stains can be expensive and sometimes not even possible. To eliminate or reduce the possibility of staining it is essential that the stone be properly protected with a good quality impregnator or sealer (in this guide the terms are synonymous).

An impregnator is a chemical that penetrates the stone and helps to repel water, dye, dirt, and other substances from causing a stain. Since the impregnator penetrates the stone (rather than coating it like wax) it allows the stone to "breath". Impregnators do not offer 100% protection from staining . If enough of a substance is left long enough it will penetrate even if the stone has been treated. Particularly oil and solvent based substances. But generally most liquids will evaporate before they would penetrate a properly impregnated stone. To limit the possibility of staining, have your stone floors treated as well as cleaning up stains quickly. Impregnation should be reapplied every 5 years or after refinishing, whichever comes first.

Call today to schedule an estimate 020 8807 0807